Unique effect of bromide ion on intensification of advanced oxidation processes for pollutants removal: a systematic review.

Advanced oxidation processes (AOPs) have been developed to decompose toxic pollutants to protect the aquatic environment. AOP has been considered an alternative treatment method for wastewater treatment. Bromine is present in natural waters posing toxic effects on human health and hence, its removal from drinking water sources is necessary. Of the many techniques advanced oxidation is covered in this review. This review systematically examines literature published from 1997 to April 2024, sourced from Scopus, PubMed, Science Direct, and Web of Science databases, focusing on the efficacy of AOPs for pollutant removal from aqueous solutions containing bromide ions to investigate the impact of bromide ions on AOPs. Data and information extracted from each article eligible for inclusion in the review include the type of AOP, type of pollutants, and removal efficiency of AOP under the presence and absence of bromide ion. Of the 1,784 documents screened, 90 studies met inclusion criteria, providing insights into various AOPs, including UV/chlorine, UV/PS, UV/H2O2, UV/catalyst, and visible light/catalyst processes. The observed impact of bromide ion presence on the efficacy of AOP processes, alongside the AOP method under scrutiny, is contingent upon various factors such as the nature of the target pollutant, catalyst type, and bromide ion concentration. These considerations are crucial in selecting the best method for removing specific pollutants under defined conditions. Challenges were encountered during result analysis included variations in experimental setups, disparities in pollutant types and concentrations, and inconsistencies in reporting AOP performance metrics. Addressing these parameters in research reports will enhance the coherence and utility of subsequent systematic reviews.

Harnessing artificial intelligence-driven approach for enhanced indole-3-acetic acid from the newly isolated Streptomyces rutgersensis AW08.

Indole-3-acetic acid (IAA) derived from Actinobacteria fermentations on agro-wastes constitutes a safer and low-cost alternative to synthetic IAA. This study aims to select a high IAA-producing Streptomyces-like strain isolated from Lake Oubeira sediments (El Kala, Algeria) for further investigations (i.e., 16S rRNA gene barcoding and process optimization). Subsequently, artificial intelligence-based approaches were employed to maximize IAA bioproduction on spent coffee grounds as high-value-added feedstock. The specificity was the novel application of the Limited-Memory Broyden-Fletcher-Goldfarb-Shanno Box (L-BFGS-B) optimization algorithm. The new strain AW08 was a significant producer of IAA (26.116 ± 0.61 µg/mL) and was identified as Streptomyces rutgersensis by 16S rRNA gene barcoding and phylogenetic inquiry. The empirical data involved the inoculation of AW08 in various cultural conditions according to a four-factor Box Behnken Design matrix (BBD) of Response surface methodology (RSM). The input parameters and regression equation extracted from the RSM-BBD were the basis for implementing and training the L-BFGS-B algorithm. Upon training the model, the optimal conditions suggested by the BBD and L-BFGS-B algorithm were, respectively, L-Trp (X1) = 0.58 %; 0.57 %; T° (X2) = 26.37 °C; 28.19 °C; pH (X3) = 7.75; 8.59; and carbon source (X4) = 30 %; 33.29 %, with the predicted response IAA (Y) = 152.8; 169.18 µg/mL). Our findings emphasize the potential of the multifunctional S. rutgersensis AW08, isolated and reported for the first time in Algeria, as a robust producer of IAA. Validation investigations using the bioprocess parameters provided by the L-BFGS-B and the BBD-RSM models demonstrate the effectiveness of AI-driven optimization in maximizing IAA output by 5.43-fold and 4.2-fold, respectively. This study constitutes the first paper reporting a novel interdisciplinary approach and providing insights into biotechnological advancements. These results support for the first time a reasonable approach for valorizing spent coffee grounds as feedstock for sustainable and economic IAA production from S. rutgersensis AW08.

New insights on the decolorization of waste flows by Saccharomyces cerevisiae strain - A systematic review.

One of the common causes of water pollution is the presence of toxic dye-based effluents, which can pose a serious threat to the ecosystem and human health. The application of Saccharomyces cerevisiae (S. cerevisiae) for wastewater decolorization has been widely investigated due to their efficient removal and eco-friendly treatments. This review attempts to create an awareness of different forms and methods of using Saccharomyces cerevisiae (S. cerevisiae) for wastewater decolorization through a systematic approach. Overall, some suggestions on classification of dyes and related environmental/health problems, and treatment methods are discussed. Besides, the mechanisms of dye removal by S. cerevisiae including biosorption, bioaccumulation, and biodegradation and cell immobilization methods such as adsorption, covalent binding, encapsulation, entrapment, and self-aggregation are discussed. This review would help to inspire the exploration of more creative methods for applications and modification of S. cerevisiae and its further practical applications.

Phytofabrication of silver nanoparticles using Averrhoa bilimbi leaf extract for anticancer activity.

Averrhoa bilimbi leaf extract was successfully utilized as a reducing agent to synthesize silver nanoparticles (AgNPs) in the laboratory. The phytochemicals in the extract helped keep the silver nanoparticles stable and slowed them down. Different methods, such as UV-visible, FT-IR spectroscopies, XRD, and SEM analyses, were used to characterize the size, shape, and morphology of the nanoparticles, and the results showed that the synthesized nanoparticles were spherical and monodispersed. FTIR spectrum streaching vibrations shown stabillization of silver nanoparticles by green extract. On the other hand, these nanoparticles were labelled as Averrhoa bilimbi (AB) extract silver nanoparticles (AB-AgNPs). The biological synthesis process was proven to enhance the efficacy of the synthesized silver nanoparticles. The effectiveness of AB-AgNPs in fighting cancer could be enhanced specifically for lung cancer (A549 cell line) and breast cancer (MCF7 cell line) by optimizing the necessary conditions. The IC50 value for A549 cells was 49.52 g mL-1, while that for MCF7 cells was 78.40 g mL-1. The effect of AgNPs on both cell lines was assessed using an MTT assay, which showed a dose-dependent cytotoxicity effect. The biosynthesized AB-AgNPs hold great potential as anticancer agents. Their synthesis using Averrhoa bilimbi leaf extract as a reducing agent was proven to be successful, resulting in spherical and monodispersed nanoparticles that exhibit effective cytotoxicity against cancer cells.

Polymeric hydrogels-based materials for wastewater treatment.

Low-cost and reliable wastewater treatment is a relevant issue worldwide to reduce the concentration of environmental pollutants. Industrial effluents containing dyes, heavy metals, and other inorganic and organic compounds can pollute water resources; therefore, novel technologies are required to mitigate and control their release into the environment. Adsorption is one of the simplest methods for treating contaminated water in which a wide spectrum of adsorbents can be used to remove emerging compounds. Hydrogels are interesting materials with high adsorption capacities that can be synthesized via green routes. These adsorbents are promising for large-scale industrial wastewater treatment applications; however, gaps still exist in achieving sustainable commercial implementation. This review focuses on the discussion and analysis of preparation, characterization, and adsorption properties of hydrogels for water purification. The advantages of these polymeric materials for water treatment were analyzed, including their performance in the removal of different organic and inorganic contaminants. Recent advances in the functionalization of hydrogels and the synthesis of novel composites have also been described. The adsorption capacities of hydrogel-based adsorbents are higher than 500 mg/g for different organic and inorganic pollutants, and can reach values of up to >2000 mg/g for organic compounds, significantly outperforming other materials reported for water cleaning. The main interactions involved in the adsorption of water pollutants using hydrogel-based adsorbents were described and explained to allow the interpretation of their removal mechanisms. The current challenges in the implementation of hydrogels for water purification in real-life operations are also highlighted. This review provides an updated picture of hydrogels as interesting materials to address water depollution worldwide.

Zn and Co ferrite nanoparticles: towards the applications of sensing and adsorption studies.

An important deliberation of this current work is the impending applications of bivalent transition metals doped with nano ferrites and to study their emerging properties of magnetically active ferrites, which constitute oxides of iron (different conformers most demanding γ-Fe2O3) and transition metal complexes of bivalent metal oxides like cobalt (Co(II)) and magnesium (Mg(II)). Fe3+ ions occupy tetrahedral sites; the rest of Fe3+ and the Co2+ ions occupy octahedral sites. For the synthesis, a self-propagating method of combustion at lower temperature was used. Zinc and cobalt nano ferrites are synthesized from the chemical coprecipitation method of 20 to 90 nm in average size, characterized thoroughly employing FTIR and PXRD and surface morphology studied using SEM. These results explain the existence of ferrite nanoparticles in cubic spinel. Magnetically active metal oxide nanoparticles are now commonly employed in main studies of sensing, absorption, and other properties. All studies showed the interesting results.

Anticancer potential of biologically synthesized silver nanoparticles using Lantana camara leaf extract.

A Lantana camara leaf (LC) extract was used as a mild reducing agent to produce silver metal nanoparticles (LC-AgNPs) efficiently. The size, shape, and morphology of synthesized silver nanoparticles were verified. LC-AgNPs were found in LC extract by XRD. The optimal concentrations of silver nitrate and LC extract necessary for the production of stable silver nanoparticles were determined. The LC-AgNPs were found spherical in form and monodispersed. Under optimal conditions, the round LC-AgNPs of 50-90 nm were utilized to cure lung cancer (A549 cell line) and breast cancer (MCF7) cell lines. Finally, the produced LC-AgNPs enhanced anti-cancer efficacy against A549 cells, with an IC50 = 49.52 g/mL. Similarly, the effect of LC-AgNPs on MCF7 cell line was assessed using an MTT test and inhibitory concentration (IC50) was determined found that 46.67 g/mL.

Adsorption modelling and fixed-bed column study on milk processing industry wastewater treatment using chitosan zinc-oxide nano-adsorbent-coated sand filter bed.

This study aims to develop a chitosan-zinc oxide nano-adsorbent-coated sand (CZOCS) filter bed for getting rid of milk processing industry wastewater (MPIW) in a safe way. Chitosan zinc oxide nano-adsorbent (CZnO) of 88.35 ± 2.89 d.nm size was used to coat naturally available sand through a calcination process at 200 °C for a heating rate of 5 °C/min. The characteristics of the diffraction peaks and functional groups are attributed to the nature of CZnO loading on the sand surface. The increase in breakthrough and exhaustion times is caused by the biological oxygen demand (BOD) and chemical oxygen demand (COD) of influent having more time to interact with the adsorbent as bed height increases, resulting in higher reduction efficiencies. Lower bed heights (10 cm) which saturate faster than higher bed heights (40 cm) result in a shorter mass transfer time. Adsorption capacity at the 95% column exhaustion point increased from 611.04 to 1089.63 mg/g for BOD and from 4512.29 to 5600.81 mg/g for COD. Different kinds of kinetic models have been used to forecast breakthrough curves employing experimental data. Statistical and error function parameters were used to choose the best-fit model. Among the models investigated, the Thomas model was shown to be the best-fit with the highest R-square values of 0.9942 and 0.9939. The CZOCS has high reusability and could be used for up to six cycles of organic pollutant adsorption. Aside from that, novel CZOCS could be used to clean real MPIW, and making it one of the most promising adsorbents.

Adsorptive removal of organic pollutants from milk-processing industry effluents through chitosan-titanium dioxide nanoadsorbent-coated sand.

Milk-processing industry effluent (MPIE) poses severe problems for aquatic and environmental systems, especially in the South Asian region. Therefore, its treatment is of great interest. This study deals with the investigation of chitosan titanium dioxide nanoadsorbent (CTiO2) coated onto sand particles via calcination that are used to remove the emerging pollutants. The adsorptive properties of these developed adsorbents are compared with those of the nascent sand without coating as well as with the chitosan titanium dioxide nanoadsorbent coated sand (CTiO2-CS). Batch adsorption experiments were performed to investigate the percent reduction efficiency (%RE) of organic pollutants in terms of biological oxygen demand (BOD) and chemical oxygen demand (COD) from synthetic and real effluents. The maximum %RE of BOD (96.76) and COD (98.91) was achieved at 1.5 M dose of CTiO2-CS, 120 min of contact time, pH 6.5, an initial BOD concentration of 900 mg/L, and an agitation speed of 400 rpm. Similarly, the %RE of COD was found to be 86.75 for synthetic effluent and 90.97 for real effluent at initial COD concentrations of 8000 mg/L. Pseudo-second-order and Langmuir models are found to be the best fits for BOD and COD adsorption. The diffusion model suggests that surface adsorption as well as intraparticle diffusion contribute to the actual adsorption process. Regeneration experiments were performed for four cycles, and CTiO2-CS was found to be the most regenerable adsorbent material. The performance of the adsorbent was compared with previous studies, and it was found to have excellent adsorption capacity. As a result, the developed filter bed could be used as a promising superadsorbent for the removal of organic load in MPIE.

Assessment of Destructive and Nondestructive Analysis for GGBS Based Geopolymer Concrete and Its Statistical Analysis.

Geopolymer is the alternative to current construction material trends. In this paper, an attempt is made to produce a sustainable construction composite material using geopolymer. Ground granulated blast furnace slag (GGBS)-based geopolymer concrete was prepared and tested for different alkaline to binder ratios (A/B). The effect of various temperatures on compressive strength properties was assessed. The cubes were exposed to temperature ranging from 50 to 70 °C for a duration ranging from 2 to 10 h, and the compressive strength of the specimens was analyzed for destructive and non-destructive analysis and tested for 7, 28, and 90 days. The obtained compressive strength (CS) results were analyzed employing the probability plot (PP) curve, distribution overview curve (DOC), probability density function (PDF), Weibull, survival, and hazard function curve. Maximum compressive strength was achieved for the temperature of 70 °C and an A/B of 0.45 for destructive tests and non-destructive tests with 44.6 MPa and 43.56 MPa, respectively, on 90 days of testing. The survival and hazard function curves showed incremental distribution characteristics for 28 and 90 days of testing results with a probability factor ranging from 0.8 to 1.0.

Optimization of Alkaline Activator on the Strength Properties of Geopolymer Concrete.

This study investigates the effects of red mud on the performance of geopolymer concrete in regard to fresh and mechanical properties. Red mud was used as a binder, and GGBS replaced the binder. Different proportions of red mud ranging from 0 to 30% with an interval of 2% and activator agents such as KOH and K2SiO3 for various alkaline-to-binder ratios such as 0.30, 0.40, and 0.50 were used; their effect on the fresh and mechanical properties of geopolymer concrete were the focusing parameter on the current study. Fresh properties such as setting time, slump, compaction factor, and vee-bee consistometer test, and mechanical properties such as compressive strength, split tensile strength, flexural strength, modulus of elasticity, and impact energy were studied. ANOVA and radar plot analysis were studied for various alkaline to binder (A/B) compressive strength results tested for 7 to 90 days. The increase of red mud quantity caused the decline of workability, but there was continuous enhancement of mechanical properties of GPC up to a specific limit. An alkaline-to-binder ratio of 0.4 shows excellent results compared with other ratios at ambient conditions for strength properties. ANOVA and radar plot reveal that A/B of 0.40 for 90 days shows excellent results compared with other ratios, and CS values vary in a linear manner.

Review on the Relationship between Nano Modifications of Geopolymer Concrete and Their Structural Characteristics.

The main objective of this review is to study some important nanomaterials and their impact on the performance of geopolymer concrete. This paper is an investigation into trends and technology in the development of different nanomaterials to develop higher structural performance geopolymer concrete. The effect of the alkaline to binder and sodium silicate to sodium hydroxide ratio on the performances of geopolymer performances is studied. The relationship between setting time and slump is evaluated through the ternary plot, the variation in compressive strength values is evaluated using the kernel density plot, and the relationship between split tensile and flexural strength is investigated using the scattering interval plot. Regression analysis is carried out among water absorption and bulk-density result values obtained from previous literature. As the molarity and alkaline to binder (A/B) ratios increase, the strength development of geopolymer concrete increases up to a specific limit. The addition of a small quantity of nanomaterials, namely, nano silica, nano alumina, carbon nano tubes, and nano clay, led to the maximum strength development of geopolymer concrete. Incorporating these nanomaterials into the geopolymer significantly refines the structural stability, improving its durability. The various products in GP composites emerging from the incorporation of highly reactive SEM, XRD, and FTIR analysis of nanomaterials reveal that the presence of nanomaterials, which enhances the rate of polymerization, leads to better performance of the geopolymer.

Evaluation of the Effect of Granite Waste Powder by Varying the Molarity of Activator on the Mechanical Properties of Ground Granulated Blast-Furnace Slag-Based Geopolymer Concrete.

Industrial waste such as Ground Granulated Blast-Furnace Slag (GGBS) and Granite Waste Powder (GWP) is available in huge quantities in several states of India. These ingredients have no recognized application and are usually shed in landfills. This process and these materials are sources of severe environmental pollution. This industrial waste has been utilized as a binder for geopolymers, which is our primary focus. This paper presents the investigation of the optimum percentage of granite waste powder as a binder, specifically, the effect of molar and alkaline to binder (A/B) ratio on the mechanical properties of geopolymer concrete (GPC). Additionally, this study involves the use of admixture SP-340 for better performance of workability. Current work focuses on investigating the effect of a change in molarity that results in strength development in geopolymer concrete. The limits for the present work were: GGBS partially replaced by GWP up to 30%; molar ranging from 12 to 18 with the interval of 2 M; and A/B ratio of 0.30. For 16 M of GPC, a maximum slump was observed for GWP with 60 mm compared to other molar concentration. For 16 M of GPC, a maximum compressive strength (CS) was observed for GWP with 20%, of 33.95 MPa. For 16 M of GPC, a maximum STS was observed for GWP, with 20%, of 3.15 MPa. For 16 M of GPC, a maximum FS was observed for GWP, with 20%, of 4.79 MPa. Geopolymer concrete has better strength properties than conventional concrete. GPC is $13.70 costlier than conventional concrete per cubic meter.

Statistical Analysis of Polymer Nanocomposites for Mechanical Properties.

Epoxy resins, due to their high stiffness, ease of processing, good heat, and chemical resistance obtained from cross-linked structures, have found applications in electronics, adhesives coatings, industrial tooling, and aeronautic and automotive industries. These resins are inherently brittle, which has limited their further application. The emphasis of this study is to improve the properties of the epoxy resin with a low-concentration (up to 0.4% by weight) addition of Multi-Walled Carbon Nanotubes (MWCNTs). Mechanical characterization of the modified composites was conducted to study the effect of MWCNTs infusion in the epoxy resin. Nanocomposites samples showed significantly higher tensile strength and fracture toughness compared to pure epoxy samples. The morphological studies of the modified composites were studied using Scanning Electron Microscopy (SEM).

Nanoceramic Composites for Nuclear Radiation Attenuation.

The development of radiation attenuation materials with lean cross-sections is the need of the hour. However, the inherent threat of radiations accompanying these processes is of major concern. Thus, in an attempt to shield unnecessary radiations, several novel materials have been fabricated alongside the conventional materials available. Yet, there is a need for cost-effective, efficient shielding materials that have good mechanical strength and effective shielding properties. The present work investigates ceramic composite behaviors and radiation shielding capacity reinforced with lead oxide nano-powder. Developed nano-lead-based cement composites were subjected to mechanical tests to determine flexural and compressive strengths to check their suitability for structural applications. Further, the gamma attenuation test of the composites was conducted to determine their neutron absorption capacity. The addition of nano-leadoxide in the control beams was varied from 0.7 to 0.95 and 1 wt.% of the ceramic matrix. The percentage of nano-leadoxide that gives the best results in both enhanced properties and economic aspects was determined to be 0.6 wt.% of the cement.

Biodegradable carboxymethyl cellulose based material for sustainable packaging application.

The main goal of the present work was to develop a value-added product of biodegradable material for sustainable packaging. The use of agriculture waste-derived carboxymethyl cellulose (CMC) mainly is to reduce the cost involved in the development of the film, at present commercially available CMS is costly. The main focus of the research is to translate the agricultural waste-derived CMC to useful biodegradable polymer suitable for packaging material. During this process CMC was extracted from the agricultural waste mainly sugar cane bagasse and the blends were prepared using CMC (waste derived), gelatin, agar and varied concentrations of glycerol; 1.5% (sample A), 2% (sample B), and 2.5% (sample C) was added. Thus, the film derived from the sample C (gelatin + CMC + agar) with 2.0% glycerol as a plasticizer exhibited excellent properties than other samples A and B. The physiochemical properties of each developed biodegradable plastics (sample A, B, C) were characterized using Fourier Transform Infra-Red (FTIR) spectroscopy and Differential Scanning Calorimetry (DSC), Thermogravimetric analysis (TGA). The swelling test, solubility in different solvents, oil permeability coefficient, water permeability (WP), mechanical strength of the produced material was claimed to be a good material for packaging and meanwhile its biodegradability (soil burial method) indicated their environmental compatibility nature and commercial properties. The reflected work is a novel approach, and which is vital in the conversion of organic waste to value-added product development. There is also another way to utilize commercial CMC in preparation of polymeric blends for the packaging material, which can save considerable time involved in the recovery of CMC from sugarcane bagasse.

Photo-irradiated biosynthesis of silver nanoparticles using edible mushroom pleurotus Florida and their antibacterial activity studies.

This is a report on photo-irradiated extracellular synthesis of silver nanoparticles using the aqueous extract of edible oyster mushroom (Pleurotus florida) as a reducing agent. The appearance, size, and shape of the silver nanoparticles are understood by UV-visible spectroscopy, field emission scanning electron microscopy, transmission electron microscopy, and atomic force microscopy. The X-ray diffraction studies, energy dispersive X-ray analysis indicate that particles are crystalline in nature. Fourier transform infrared spectroscopy analysis revealed that the nanoparticles are covered with biomoieties on their surface. As can be seen from our studies, the biofunctionalized silver nanoparticles thus produced have shown admirable antimicrobial effects, and the synthetic procedure involved is eco-friendly and simple, and hence high range production of the same can be considered for using them in many pharmaceutical applications.